10G Copper SFP

10G RJ45 Optical Transceiver 30m Features: • Support 10Gbase-T / 5Gbase-T / 2.5Gbase-T / 1000base-T on line port Support 10Gbase-R on host port • Hot-pluggable SFP footprint Compact RJ-45 connector assembly RoHS compliant and lead-free Single +3.3V power supply • 10 Gigabit Ethernet over Cat 6a cable Ambient Operating temperature: 0°C to +65°C Applications: • 1.25 Gigabit Ethernet over Cat 5 cable Switch/Router to Switch/Router Link High speed I/O for file severs Product Description: • ESFP-10G-RJ45 Copper Small Form Pluggable (SFP) transceivers are based on the SFP Multi Source Agreement (MSA) . They are compatible with the 10Gbase-T / 5Gbase-T • /2.5Gbase-T / 1000base-T standards as specified in IEEE Std 802.3. SFP+-10GBASE-T uses the SFP's RX_LOS (must be pulled up on host) pin for link indication. If pull up or open SFP's TX_DISABLE pin, PHY IC be reset. Cable Length: Line Port Cable Reach Host Port 10Gbase-T CAT6 A 30m 10GBase-R 5Gbase-T CAT5 E 50m 10GBase-R 2.5Gbase- T CAT5 E 50m 10GBase-R 1000base- T CAT5 E 100m 10GBase-R 100base- Tx CAT5 E 100m 10GBase-R 10base-Tx CAT5 E 100m 10GBase-R Pi n Symbol Name/Descripti on Ref. 1 VEE T Transmitter Ground (Common with Receiver Ground) 1 2 TFAULT Transmitter Fault. Not supported. 3 TDI S Transmitter Disable. Laser output disabled on high or open. 2 4 MOD_DEF (2) Module Definition 2. Data line for Serial ID. 3 5 MOD_DEF (1) Module Definition 1. Clock line for Serial ID. 3 6 MOD_DEF (0) Module Definition 0. Grounded within the module. 3 7 Rate Select No connection required 8 LOS High indicates no linked. low indicates linked. 9 VEER Receiver Ground (Common with Transmitter Ground) 1 10 VEER Receiver Ground (Common with Transmitter Ground) 1 11 VEER Receiver Ground (Common with Transmitter Ground) 1 12 RD- Receiver Inverted DATA out. AC Coupled 13 RD+ Receiver Non-inverted DATA out. AC Coupled 14 VEE R Receiver Ground (Common with Transmitter Ground) 1 15 VCC R Receiver Power Supply 16 VCC T Transmitter Power Supply 17 VEET Transmitter Ground (Common with Receiver Ground) 1 18 TD+ Transmitter Non-Inverted DATA in. AC Coupled. 19 TD- Transmitter Inverted DATA in.AC Coupled. 20 VEET Transmitter Ground (Common with Receiver Ground) 1 Notes: • Circuit ground is connected to chassis ground • PHY disabled on TDIS > 2.0V or open, enabled on TDIS < 0.8V • Should be pulled up with 4.7k - 10k Ohms on host board to a voltage between 2.0 V and 3.6 • V. MOD_DEF (0) pulls line low to indicate module is plugged in. Figure 1. Diagram of host board connector block pin numbers and names +3.3V Volt Electrical Power Interface: The ESFP-10G-RJ45 has an input voltage range of 3.3 V +/- 5%. The 4V maximum voltage is not allowed for continuous operation. +3.3 Volt Electrical Power Interface Parameter Symbol Min Type Max unit Notes/Conditions Supply Current Is 700 900 mA 3.0W max power over full range of voltage and temperature. See caution note below Input Voltage Vcc 3.13 3.3 3.47 V Referenced to GND Maximum Voltage Vmax 4 V Surge Current Isurge TBD mA Hot plug above steady state current. See caution note below Caution: Power consumption and surge current are higher than the specified values in the SFP MSA Low-Speed Signals: • MOD_DEF(1) (SCL) and MOD_DEF (2) (SDA), are • open drain CMOS signals (see section VII, "Serial Communication Protocol"). Both MOD_DEF (1) and MOD_DEF (2) must be pulled up to host Vcc Low-Speed Signals, Electronic Characteristics Parameter Symbol Min Max unit Notes/Conditions SFP Output LOW VO L 0 0.5 V 4.7k to 10k pull-up to host_Vcc, measured at host side of connector SFP Output HIGH VOH host_Vcc-0.5 Host Vcc + 0.3 V 4.7k to 10k pull-up to host_Vcc, measured at host side of connector SFP Input LOW VIL 0 0.8 V 4.7k to 10k pull-up to Vcc, measured at SFP side of connector SFP Input HIGH VIH 2 Vcc + 0.3 V 4.7k to 10k pull-up to Vcc, measured at SFP side of connector High-Speed Electrical Interface: All high-speed signals are AC-coupled internally. High-Speed Electrical Interface, Transmission Line-SFP Parameter Symbol Min Typ Max unit Notes/Conditions Line Frequency fL 125 MHz 5-level encoding, per IEEE 802.3 Tx Output Impedance Zout,T X 100 Ohm Differential, for all frequencies between 1MHz and 125MHz Rx Input Impedance Zin,R X 100 Ohm Differential, for all frequencies between 1MHz and 125MHz High-Speed Electrical Interface, Transmission Line-SFP Parameter Symbol Min Typ Max unit Notes/Conditions Line Frequency fL 125 MHz 5-level encoding, per IEEE 802.3 Tx Output Impedance Zout,TX 100 Ohm Differential, for all frequencies between 1MHz and125MHz Rx Input Impedance Zin,R X 100 Ohm Differential, for all frequencies between 1MHz and 125MHz Rise/Fall Time Tr,Tf 175 psec 20%-80% Tx Input Impedance Zin 50 Ohm Single ended Rx Output Impedance Zout 50 Ohm Single ended General Specifications: General Parameter Symbo l Min Type Max unit Notes/Conditions Data Rate BR 1 10 Gb/sec IEEE 802.3 compatible. See Notes 1,2 below Notes: Clock tolerance is +/- 50 ppm EEPROM INFORMATION（A0）: Addr Field Size (Bytes) Name of Field HEX Description 0 1 Identifier 03 SFP 1 1 Ext. Identifier 04 MOD4 2 1 Connector 22 RJ45 3-10 8 Transceiver 00 00 00 00 00 00 00 00 Transmitter Code 11 1 Encoding 06 64B66B 12 1 BR, nominal 67 10000M bps 13 1 Reserved 00 14 1 Length (9um)-km 00 15 1 Length (9um) 00 16 1 Length (50um) 08 80 17 1 Length (62.5um) 03 30 18 1 Length (copper) 00 19 1 Reserved 1E 30 20-35 16 Vendor name 57 49 4E 54 4F 50 20 20 20 20 20 20 20 20 20 20 EFYLINK 36 1 Reserved 00 37-39 3 Vendor OUI 00 00 00 40-55 16 Vendor PN xx xx xx xx xx xx xx xx xx xx xx xx xx xx xx xx ASC II 56-59 4 Vendor rev 31 2E 30 20 V1.0 60-61 2 Wavelength 00 00 850nm 62 1 Reserved 00 63 1 CC BASE X X Check sum of byte 0~62 64-65 2 Options 00 1A LOS, TX_DISABLE, TX_FAULT 66 1 BR, max 00 67 1 BR, min 00 68-83 16 Vendor SN 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 Unspecified 84-91 8 Vendor date code XX XX XX 20 Year, Month, Day 92-94 3 Reserved 00 95 1 CC_EXT X X Check sum of byte 64~94 96-255 160 Vendor specific EEPROM INFORMATION（A2, optional: Environmental Specifications: • Automatic crossover detections enabled. External crossover cable is not required Environmental Specifications Parameter Symbol Min Typ Max unit Notes/Conditions Operating Temperature Top 0 65 °C Case temperature Storage Temperature Tsto -40 85 °C Ambient temperature Serial Communication Protocol: • All SFPs support the 2-wire serial communication protocol outlined in the SFP MSA. These SFPs use an MCU, can be accessed with address of A0h. Serial Bus Timing, Requirements Parameter Symbol Min Typ Max unit Notes/Conditions I 2C Clock Rate 0 200,00 0 Hz Recommended Application Circuit: Mechanical Specifications (Unit: mm): Order Information: Part Number Product Description SFP10GC-AT 10G Copper SFP